Description
Product Description
Specification:
Origin: Mainland China
Package Size: 120.00×100.00×20.00mm/4.72×3.94×0.79inch
Place of Origin (Country or Region): Mainland China (Origin)
A: NGFF+NGFF to SATA Integration Card
Size: 10*7*0.9cm/3.9*2.7*0.35in
Dual M.2 NGFF-SATA interfaces, nvme pci-e protocol not supported
Product Features:
1.Only support M.2SATA protocol SSD use, does not support NME protocol and PC-E protocol SSDs
2 must be inserted at the same time 2 SSD in order to use, try to the same brand specifications will be compatible with a good point
3. The first time you use the SSD will reset the initialisation of the SSD, back up your hard drive information before use.
4. When using 2 hard drives to form a JBOD, 2 discs into a disk
B :NGFF+MSATA to SATA Integration Card
Size: 10*7*0.7cm/3.9*2.7*2.7in
M.2 NGFF-SATA+MSATA interface, does not support nvme pci-e protocol
Product Features:
1.Adapt mSATA and M,2SATA defined hard drive to SATA 22PIN interface
2.You must plug in 2 discs at the same time to use it! If there is only one hard disc, please buy a single port adapter card.
3. The first time you use the first repair tool to repair the partition formatting
4. This adapter is a dual-disk JB0OD mode, that is, the capacity to add up. 2 discs into a disc!
C:NGFF+MSATA to SATA Dual Purpose Card
Size: 10*7*0.7cm/3.9*2.7*2.7in
Two SSDs can be inserted at the same time, only one SSD can be recognised at a time, the switch needs to be flicked to the corresponding position in the NGFF sectionThis adapter is only suitable for B-key or B/M-key interface, not for M-key interface. The adapter only works with B-key or B/M-key interfaces, not with M-key interfaces. Use a switch design that does not support the AHCI and NVME protocols, with the NGFF mode switch switching up and the MSATA mode switch switching down.
Use only m2 drives that support the SATA protocol (NGFF):
1. Converts SSDs to support M.2 NGFF or MSATA to SATA2.5"/3.5" drives.
2. Fully compatible with SATA3.1 standard
3. Compatible with PCI Express M.2 protocol
4. NGFF and MSATA SSDs allow an input voltage of 3.3V and a maximum current of 3A. This adapter has no chip, so there is no speed or anything like that. It only acts as a transfer function. The speed is related to the SSD itself.
5. Support 80mm 60mm 42mm 30mm M.2 NGFF SSDs
6. Supports full-height and half-height size MSATA SSDs
D:NGFF to SATA single interface
Size: 10.2*4.8cm/4.0*1.8in
Function:
1. Convert M.2 NGFF SSD to 2.5-inch SATA (6Gbps) interface
2. M.2 NGFF SSD to 2.5-inch SATA adapter converter supports SATA-based B key and B+M key M.2 SSDs
3. Maximise system speed by increasing M.2 SSD performance
4. Reduce overall power consumption with efficient M.2 SSDs
5. Supports SATA Revision I/II/III (1.5/3.0/6.0 Gbps)
6. Supports full-length M.2 NGFF (Next Generation Form Factor) SSDs (2230, 2242, 2260, 2280)
Caution:
It does not support PCI-e based "M key" or "M+B key" (NVME AHCI) SSDs.
E:MSATA to SATA single interface
Size: Approx. 57x46mm/ 2.24×1.81"
Support 30mm*50mm size mSATA SSD converted to standard 2.5" SATA6.0Gbps interface
Both backwards SATA 3.0Gbps and SATA 1.5Gbps
Properties such as speed are unchanged, just the form-factor conversion interface, as such a conversion does not need to go through an integrated circuit chip
You can connect it to your laptop or desktop without any driver.
This product only supports mSATA Mini PCIE SSDs, not SATA Mini PCIE SSDs and PATA Mini PCIE SSDs.
Note:
Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!
Please allow 1-2cm measuring deviation due to manual measurement.
Package Content:
1 x M2 SATA Adapter
Reviews
There are no reviews yet.